The task of restoring your old house by retiling the entire walls or changing the appearance requires a lot of work. Whatever the cause, you can either replace the old tiles, repaint them, or cover them with new wallpapers.
The first one is more expensive than the rest. However, if you want to replace the old tiles, you may face issues with the adhesives stuck to the wall.
Tools You Need to Remove Adhesive
A multi-tool is the quickest and easiest tool to remove adhesive. However, you can use the typical scraper and a paintbrush to rub off the glue residues.
How to Remove Old Tile Adhesive
To attach new tiles to the wood or concrete floor, you have to take off the old glue residues. It’s not an effortless job and you will need the right tile adhesive remover.
Well, don’t worry. You are going to have the easiest technique to remove old tile adhesive from the floor and walls.
What you need
For removing adhesive from old tiles, you will need a few essential components, like-
- Warm water
- Clean fabric piece
- Standard scraper,
- Face mask
- Protecting apron
- Protective plastic sheet for floor
What to Use to Soft the Adhesive Residues:
Now, you can apply any of the following materials:
- Warm water: Most of the time, it’s easier to remove old tile glue; you just have to apply warm water to it.
- Hot water & steam: When the old glues are too hard to get softened and warm water alone is not efficient, you can use hot water. Also, you will get a better result by using steam.
- Commercial glue remover: Some old glues will not be easy to remove just with water or steam. You should go with an industrial-grade remover. And in that case, citric acid-based remover should be your first choice that is less hazardous. Therefore, you can use it anywhere inside your home. For the best tile adhesive remover, check this article.
So how to remove old floor tile adhesive with the above materials? Lets’ check the easy steps with warm water first.
- Clean the surface: First, clean the tiles with a damp cloth to make the glue melt fast.
- Use warm water: You can directly spray the water on glues. Else, you can wet the clean fabric with warm water and soak the tiles up.
- Use paintbrush: After applying warm water, brush the remnants a little.
- Wait some minutes: After using heated water on the floor tiles, wait for a few minutes to allow the glues to absorb the water and become soft.
- Scrape off: Once the residues are soft, use a scraper to strip the adhesive remainders. Also, you can rub them off with a paintbrush.
- Repeat: Repeat the process until all remnants are gone, and you can not feel any sticky touch.
- Sometimes you may find old resin mastics to be removed. You need to be cautious not to use a hot gun on those because mastics can easily be set on fire.
- Some kinds of tile adhesive may need more amount of remover than others.
- While using the steaming methods on plasterboard walls, take extra caution so that you will not blow the plaster. Do not hold the steamer in one place, not longer than 30 seconds.
- If you are going to work with isolated tiles, you can soak them in hot water. This will save you time and energy.
- Always take consultancy or help from professionals.
- Read the manuals well before using an industrial remover.
When to Use Steam to Remove Tiles Adhesive from Walls and Floors
Warm water alone will not work well on old glues that are hardened, and you must apply steams for a better result.
However, while using a hot steamer, you need to remember the following things:
- Work on small area: The glue residues will get softened at first but will turn hard once they lose the heat. Therefore, you should work on a small area at a time and wipe it off.
- Start from the top: When using wallpaper steamer, select 3-4 tiles from any corner on the top of the walls. And then move the steamer slowly over them.
- Apply steam precisely: Don’t levitate steamer on a single spot for more than 20 seconds; it may cause damage to the concrete mixtures.
- Scrape off: Once the adhesive remnants become soft, simply rub them off.
- Repeat: Finally, repeat the process until all the walls get rid of glues.
For using the steamer on the floor or sub-floor, the process is the same as the wall.
How to Remove Tile Glue from Wall
The process for removing tile adhesive from the wall is the same as what you have to follow in how to remove floor tile adhesive. The extra thing you have to do here is cover the bottom with plastic sheets. While the residues fall off the wall tiles, they will arrive on the plastic sheets, and the floor will be protected from dirty remains.
How to Remove Dried Tile Adhesive from Tiles
While applying glues on new tiles, sometimes you may misplace them, and you need to remove them. The job is with a wet cloth till they are moist and soft. However, there may still be stains on the tiles as not all the glues do not entirely get off while they are wet.
You should not try to waste resources on the remains. Let them dry and hard. And then just follow the same steps you followed for removing old tile glue.
How to Remove Ceramic Tile Adhesive from Concrete Floor
You will see mainly six types of tiles are used for the concrete floors:
- Porcelain Tile
- Ceramic Tile
- Marble Tile
- Granite Tile
- Natural Stone Tile
- Glass Tile
Ceramics tiles are popular due to their fancy designs, stability, and affordability. However, they are mainly made of clay, and that’s why removing old glues is a tiresome task.
Anyway, while removing stains from ceramic tiles, you will see four types of adhesives used on a concrete floor. Check the following sections to know how to remove adhesive stains from them.
An adhesive mix of cement, water, and fine sand, though it is not water-soluble. It is also known as mortar.
As they do not absorb moisture, they are hard and crispy. Therefore, using a chisel to scrape off the glues is more efficient than a regular scraper. Well, use the chisel at a 45-degree angle so that the pressure only works horizontally and your tiles do not get broken or scratched.
It’s an organic glue made from the adhesive resin of a mastic tree, which is water-soluble. And for the same reason, it’s easy to clean the remnants simply with warm water. Get a wet towel and lay it over the floor tiles. Once they absorb the water and become soft, simply scrape off the residues.
Asbestos-based adhesives are older than others, and one of the most common floor tile adhesives is referred to as black asbestos mastic. They might become airborne, hence you should protect yourself from direct contact with them.
So, how to remove asbestos tile glue? We recommend you use professional services instead of doing it yourself.
Vinyl Flooring Adhesive
It will be more challenging to remove vinyl adhesive if it has been for a few years as its adhering strength is much than other tile adhesives. However, with the proper technique, this can be removed easily.
The first approach is to use a hot blower gun. However, do not directly heat over the vinyl tile adhesives and use some pieces of paper. And then use a scraper or knife to rub them off after they become soft.
Replacing floor and wall tiles is sometimes a must for your home. However, whether you will reuse the old tiles or attach new tiles, removing adhesive remnants from the old tiles, floor, or walls needs to be handled carefully. We hope you have understood the basic idea of how to get your job done. And if you have issues removing superglue from tiles, follow this excellent article.